DFU Mode

DFU or Device Firmware Upgrade mode allows all devices to be restored from any state. It is essentially a mode where the BootROM can accept iBSS. DFU is part of the SecureROM which is burned into the hardware, so it cannot be removed. On A7+ devices, it generates an ApNonce and recognizes APTickets as well, so even in DFU, it can accept an APTicket.

Entering DFU Mode

NOTE: If you are using a USB-C cable to enter DFU mode, it might not work. If this happens, you need to use the normal USB cable. You can use a normal USB cable and a USB to USB-C adaptor.

Apple TV

1. Plug the device into your computer using a Micro-USB cable.
2. Force the device to reboot by holding down the "Menu" and "Down" buttons simultaneously for 6-7 seconds.
3. Press "Menu" and "Play" simultaneously right after reboot, until a message pops up in iTunes, saying that it has detected an Apple TV in Recovery Mode.

A9 and older devices (iPad other than the ones listed below, iPhone 6s and below, iPhone SE and iPod touch 6 and below)

1. Connect the device to a computer using a USB cable.
2. Hold down both the Home button and Lock button.
3. After 8 seconds, release the Lock button while continuing to hold down the Home button.
   • If the Apple logo appears, the Lock button was held down for too long.
4. Nothing will be displayed on the screen when the device is in DFU mode. If open, iTunes will alert you that a device was detected in recovery mode.
   • If your device shows a screen telling you to connect the device to iTunes, retry these steps.

A10 devices (iPhone 7 and iPhone 7 Plus, iPad 2018, iPod touch 7)

1. Connect the device to a computer using a USB cable.
2. Hold down both the Side button and Volume Down button.
3. After 8 seconds, release the Side button while continuing to hold down the Volume Down button.
   • If the Apple logo appears, the Side button was held down for too long.
4. Nothing will be displayed on the screen when the device is in DFU mode. If open, iTunes will alert you that a device was detected in recovery mode.
   • If your device shows a screen telling you to connect the device to iTunes, retry these steps.

A11 and newer devices (iPhone 8 and above, iPad Pro 2018, iPad Air 2019, iPad Mini 2019)

1. Connect the device to a computer using a USB cable.
2. Quick-press the Volume Up button
3. Quick-press the Volume Down button
4. Hold down the Side button until the screen goes black, then hold down both the Side button and Volume Down button.
5. After 5 seconds, release the Side button while continuing to hold down the Volume Down button.
   • If the Apple logo appears, the Side button was held down for too long.
6. Nothing will be displayed on the screen when the device is in DFU mode. If open, iTunes will alert you that a device was detected in recovery mode.
   • If your device shows a screen telling you to connect the device to iTunes, retry these steps.

Exiting DFU Mode

To exit DFU Mode, simply force restart your device.

• For Apple TV, hold down the "Menu" and "Down" buttons on your remote until the Apple TV reboots.
• For iPad, iPhone 6s and below, iPhone SE and iPod touch, hold the Home button and the Lock button until the device reboots.
• For iPhone 7 and iPhone 7 Plus, hold down the Side button and Volume Down button until the device reboots.
• For iPhone 8, iPhone 8 Plus, and iPhone X, quick-press the Volume Up button, then quick-press the Volume Down button, then hold down the Side button until the device reboots.

Enter True Hardware DFU Mode Automatically

The EnterDFU function in the MobileDevice Library does not enter the true DFU Mode in the hardware. It's possible to enter the true DFU Mode without doing it manually, but it cannot be exited unless a restore is performed, as it creates a DFU Loop. This doesn't work with S5L8900 devices.

Steps

1. Make a copy of a fresh IPSW file.
2. Open the IPSW as a zip folder and browse to /firmware/all_flash/all_flash.xxxxx.production/
3. Extract LLB.*****.RELEASE.img3/im4p and open it in a hex editor.
4. Change some random bit or bits, it doesn't matter which or what you write.
5. Add the edited file back to the zip, rename zip to ipsw and restore it to your device using iTunes.
6. The restore will error out and your device will be in DFU Mode.

Alternative Method

If the previous method does not work for you, try this one.

1. Do steps 1 and 2 from above.
2. Delete LLB.*****.RELEASE.img3.
3. Copy applelogo.********.img3 to temporary directory.
4. Rename the copy of applelogo.********.img3/im4p to LLB.*****.RELEASE.img3/im4p. (If you forget the name of the LLB file, you can find it again in the file named manifest.)
5. Copy the renamed applelogo file back to the all_flash.xxxxx.production directory.
6. Rename the zip.
7. Restore the file using iTunes. (If every thing goes well, you should receive an error 31 from iTunes.)

DFU Mode Output to the computer

iProduct: "Apple Mobile Device (DFU Mode)"

iSerialNumber: "CPID:XXXX CPRV:15 CPFM:03 SCEP:03 BDID:00 ECID:XXXXXXXXXXXXXXXX SRTG:[iBoot-XXX.X.X]"

Revisions

S5L8900 (0x1222)

This is the device ID in the iPod touch, the iPhone, and the iPhone 3G. For more information about the protocol, see DFU 0x1222.

S5L8720, S5L8920, and WTF mode post-2.0 (0x1227)

This is the device ID in the iPod touch (2nd generation), the iPhone 3GS, the iPhone 4, subsequent 32 bit devices, all 64 bit devices, and WTF mode. For more information on the protocol, see DFU 0x1227.