|
The iPhone Wiki is no longer updated. Visit this article on The Apple Wiki for current information. |
Difference between revisions of "Baseband Commands"
(Replacing page with 'Hacked by Chroniccommand') |
m (→Running Minicom 2.2 from MobileTerminal: Fix MobileTerminal page link.) |
||
| (9 intermediate revisions by 7 users not shown) | |||
| Line 1: | Line 1: | ||
| + | ==About== |
||
| − | Hacked by Chroniccommand |
||
| + | In this page, you'll find some Baseband Commands. You can use them with Minicom 2.2, that can be found on Cydia. |
||
| + | |||
| + | ==Setting up Minicom 2.2== |
||
| + | # After installing Minicom from Cydia, make sure the folder [[:/usr/etc]] exists. SSH into your iPhone and then, type: ''minicom -s''. |
||
| + | # Now, select ''Serial Port Setup'' in the Menu and press Enter. Then, press "a" and set Serial Device to ''[[:/dev/tty.debug]]'' (however, ''[[:/dev/dlci.spi-baseband.extra_13]]'' or ''[[:/dev/dlci.spi-baseband.extra_0]]'' also works and appears to be more reliable than the other device). |
||
| + | # Press Esc, and in the Main Menu, select ''Save setup as dfl''. Now, select "exit". |
||
| + | # To run minicom using ssh, just run ''minicom -w'' |
||
| + | |||
| + | ==Running Minicom 2.2 from MobileTerminal== |
||
| + | '''Note''': minicom does work on MobileTerminal only on root (use su) and only after it has been configured (through the steps above). |
||
| + | # Open [[MobileTerminal|MobileTerminal.app]]. |
||
| + | # Run the command su, enter your root password (default alpine) and then run ''minicom -w''. |
||
| + | # To exit minicom, slide your finger on the screen ("gesture") to the bottom right (if you haven't changed this setting in MobileTerminal settings), then press A, X and enter. |
||
| + | |||
| + | ==How to run Baseband Commands== |
||
| + | First, run Minicom. Then, type "at" and press Enter. Then, you can type the command that you want, have fun. |
||
| + | |||
| + | ==Baseband Commands== |
||
| + | {{main|List of baseband commands}}. |
||
| + | |||
| + | ===Getting Information=== |
||
| + | * '''at+xgendata''': Display some baseband informations |
||
| + | * '''at&v''': Display the profiles in the Baseband (Active Profile, Stored Profile 0 and Stored Profile 1) |
||
| + | * '''at+clac''': Show some baseband commands |
||
| + | * '''at&h''': Show more Baseband Commands |
||
| + | * '''at+cgsn''': Show serial number from BBUpdaterExtreme |
||
| + | * '''at+xdrv=9,3''': Command from BBUpdaterExtreme |
||
| + | * '''at+cpwroff''': Powercycle baseband modem from BBUpdaterExtreme |
||
| + | * '''at+csq''': Get signal strength from BBUpdaterExtreme |
||
| + | |||
| + | ===Unlock=== |
||
| + | * '''at+clck''': Traditional unlock command |
||
| + | * '''at+xlock''': Wildcard unlock |
||
| + | * '''at+xsimstate''': Print lock state (write at+xsimstate=1 to turn on, at+xsimstate=0 to turn off) |
||
| + | |||
| + | ===SMS=== |
||
| + | * '''at+cmgf''': SMS operating mode (at+cmgf=0 - PDU, at+cmgf=1 - text) |
||
| + | * '''at+cmgs''': Send SMS (write at+cmgs="[PHONE NUMBER]"[ENTER][MESSAGE][CTRL-Z] while [ENTER] is an enter (\r\n) and [CTRL-Z] is ASCII 26) |
||
| + | |||
| + | ===General=== |
||
| + | * '''atz''': Reset modem |
||
| + | * '''ath''': Hangup modem |
||
| + | |||
| + | [[Category:Baseband]] |
||
Latest revision as of 14:12, 7 July 2014
Contents
About
In this page, you'll find some Baseband Commands. You can use them with Minicom 2.2, that can be found on Cydia.
Setting up Minicom 2.2
- After installing Minicom from Cydia, make sure the folder /usr/etc exists. SSH into your iPhone and then, type: minicom -s.
- Now, select Serial Port Setup in the Menu and press Enter. Then, press "a" and set Serial Device to /dev/tty.debug (however, /dev/dlci.spi-baseband.extra_13 or /dev/dlci.spi-baseband.extra_0 also works and appears to be more reliable than the other device).
- Press Esc, and in the Main Menu, select Save setup as dfl. Now, select "exit".
- To run minicom using ssh, just run minicom -w
Running Minicom 2.2 from MobileTerminal
Note: minicom does work on MobileTerminal only on root (use su) and only after it has been configured (through the steps above).
- Open MobileTerminal.app.
- Run the command su, enter your root password (default alpine) and then run minicom -w.
- To exit minicom, slide your finger on the screen ("gesture") to the bottom right (if you haven't changed this setting in MobileTerminal settings), then press A, X and enter.
How to run Baseband Commands
First, run Minicom. Then, type "at" and press Enter. Then, you can type the command that you want, have fun.
Baseband Commands
- Main article: List of baseband commands
.
Getting Information
- at+xgendata: Display some baseband informations
- at&v: Display the profiles in the Baseband (Active Profile, Stored Profile 0 and Stored Profile 1)
- at+clac: Show some baseband commands
- at&h: Show more Baseband Commands
- at+cgsn: Show serial number from BBUpdaterExtreme
- at+xdrv=9,3: Command from BBUpdaterExtreme
- at+cpwroff: Powercycle baseband modem from BBUpdaterExtreme
- at+csq: Get signal strength from BBUpdaterExtreme
Unlock
- at+clck: Traditional unlock command
- at+xlock: Wildcard unlock
- at+xsimstate: Print lock state (write at+xsimstate=1 to turn on, at+xsimstate=0 to turn off)
SMS
- at+cmgf: SMS operating mode (at+cmgf=0 - PDU, at+cmgf=1 - text)
- at+cmgs: Send SMS (write at+cmgs="[PHONE NUMBER]"[ENTER][MESSAGE][CTRL-Z] while [ENTER] is an enter (\r\n) and [CTRL-Z] is ASCII 26)
General
- atz: Reset modem
- ath: Hangup modem
