|
The iPhone Wiki is no longer updated. Visit this article on The Apple Wiki for current information. |
Difference between revisions of "Diags (iBoot command)"
m (Updating.) |
|||
| Line 1: | Line 1: | ||
| + | The <code>diags</code> command is an iBoot command that loads an image from an address in memory after disabling all the GPIO devices. This is meant for diagnostic purposes, so even unsigned images will be loaded. This command had no permission checks in 1.0-1.1.4 iBoots, so it was exploitable to load a patched iBoot, but in 2.0 iBoots, this command has a permission check to make sure it is not being run on a RELEASE iBoot. In 3.1+, this command was removed entirely, but is still present in DEVELOPMENT iBoots. This command can also be set as the boot-command variable. In that case, as well as if you run diags without any args, it looks for the diags image in NOR/NAND. If it doesn't find it, the command will fail. |
||
| − | This was an exploit that allowed the running of unsigned code at iBoot level, present in pre-2.0 versions of [[iBoot (Bootloader)|iBoot]]. |
||
==Credit== |
==Credit== |
||
| Line 5: | Line 5: | ||
==Exploit== |
==Exploit== |
||
| − | This is a very easy-to-use exploit. In earlier iBoots, if a parameter was given to the 'diags' command, then it would jump to whatever address argv[1] specified, but not before disabling the GPIO devices. You can run unsigned code on the [[S5L8900]] using this, but the GPIOs need to be restored if you intend to use any I/O again (such as the screen, serial, or USB). |
+ | This is a very easy-to-use exploit on 1.x iBoots. In earlier iBoots, if a parameter was given to the 'diags' command, then it would jump to whatever address argv[1] specified, but not before disabling the GPIO devices. You can run unsigned code on the [[S5L8900]] using this, but the GPIOs need to be restored if you intend to use any I/O again (such as the screen, serial, or USB). This command can still be exploited on a DEVELOPMENT iBoot in current firmwares. |
| − | In 2.0 iBoots, they have a flag check on this command (checks bit 4 of the iBoot flags), and that flag will not be present on a |
+ | In 2.0 iBoots, they have a flag check on this command (checks bit 4 of the iBoot flags), and that flag will not be present on a RELEASE iBoot, just a DEVELOPMENT iBoot, so this exploit doesn't work on RELEASE iBoots. However, the 1.1.4 [[iBSS]] can still be used on the [[M68AP|iPhone]], [[N82AP|iPhone 3G]], or [[N45AP|iPod touch]], and can be used to boot a modified 2.0+ [[iBoot (Bootloader)|iBoot]]. Therefore, it is still an open exploit for these devices. |
| − | [[Category:Exploits]] |
+ | [[Category:Exploits]] [[Category:iBoot commands]] |
Revision as of 12:55, 29 July 2016
The diags command is an iBoot command that loads an image from an address in memory after disabling all the GPIO devices. This is meant for diagnostic purposes, so even unsigned images will be loaded. This command had no permission checks in 1.0-1.1.4 iBoots, so it was exploitable to load a patched iBoot, but in 2.0 iBoots, this command has a permission check to make sure it is not being run on a RELEASE iBoot. In 3.1+, this command was removed entirely, but is still present in DEVELOPMENT iBoots. This command can also be set as the boot-command variable. In that case, as well as if you run diags without any args, it looks for the diags image in NOR/NAND. If it doesn't find it, the command will fail.
Credit
Exploit
This is a very easy-to-use exploit on 1.x iBoots. In earlier iBoots, if a parameter was given to the 'diags' command, then it would jump to whatever address argv[1] specified, but not before disabling the GPIO devices. You can run unsigned code on the S5L8900 using this, but the GPIOs need to be restored if you intend to use any I/O again (such as the screen, serial, or USB). This command can still be exploited on a DEVELOPMENT iBoot in current firmwares.
In 2.0 iBoots, they have a flag check on this command (checks bit 4 of the iBoot flags), and that flag will not be present on a RELEASE iBoot, just a DEVELOPMENT iBoot, so this exploit doesn't work on RELEASE iBoots. However, the 1.1.4 iBSS can still be used on the iPhone, iPhone 3G, or iPod touch, and can be used to boot a modified 2.0+ iBoot. Therefore, it is still an open exploit for these devices.
