|
The iPhone Wiki is no longer updated. Visit this article on The Apple Wiki for current information. |
Difference between revisions of "Baseband Commands"
m (→Setting up Minicom 2.2: - reformatting) |
m (→Baseband Commands) |
||
| Line 21: | Line 21: | ||
==Baseband Commands== |
==Baseband Commands== |
||
===Getting Information=== |
===Getting Information=== |
||
| − | '''at+xgendata''': Display some baseband informations |
+ | * '''at+xgendata''': Display some baseband informations |
| + | * '''at&v''': Display the profiles in the Baseband (Active Profile, Stored Profile 0 and Stored Profile 1) |
||
| − | |||
| + | * '''at+clac''': Show some baseband commands |
||
| − | '''at&v''': Display the profiles in the Baseband (Active Profile, Stored Profile 0 and Stored Profile 1) |
||
| + | * '''at&h''': Show more Baseband Commands |
||
| − | |||
| − | '''at+clac''': Show some baseband commands |
||
| − | |||
| − | '''at&h''': Show more Baseband Commands |
||
===Unlock=== |
===Unlock=== |
||
| − | '''at+clck''': Traditional unlock command |
+ | * '''at+clck''': Traditional unlock command |
| + | * '''at+xlock''': Wildcard unlock |
||
| − | |||
| + | * '''at+xsimstate''': Print lock state (write at+xsimstate=1 to turn on, at+xsimstate=0 to turn off) |
||
| − | '''at+xlock''': Wildcard unlock |
||
| − | |||
| − | '''at+xsimstate''': Print lock state (write at+xsimstate=1 to turn on, at+xsimstate=0 to turn off) |
||
Revision as of 01:31, 12 April 2009
Contents
About
In this page, you'll find some Baseband Commands. You can use them with Minicom 2.2, that can be found on Cydia.
Setting up Minicom 2.2
- After installing Minicom from Cydia, make sure the folder /usr/etc exists. SSH into your iPhone and then, type: minicom -s.
- Now, select Serial Port Setup in the Menu and press Enter. Then, press "a" and set Serial Device to /dev/tty.debug.
- Press Esc, and in the Main Menu, select Save setup as dfl. Now, select "exit".
- Note: minicom does work on MobileTerminal only on root (use su) and only after it has been configured.
- Run the command su, enter your root password (default alpine) and then run minicom -w.
- To exit minicom, slide your finger on the screen ("gesture") to the bottom right (if you haven't changed this setting in MobileTerminal settings), then press A, X and enter.
Running Minicom
To run minicom, is pretty simple: just type "minicom -w".
How to run Baseband Commands
Here is the list that me (pH) and EvilPenguin are doing of Baseband Commands.
First, run Minicom. Then, type "at" and press Enter. Then, you can type the command that you want, have fun.
Baseband Commands
Getting Information
- at+xgendata: Display some baseband informations
- at&v: Display the profiles in the Baseband (Active Profile, Stored Profile 0 and Stored Profile 1)
- at+clac: Show some baseband commands
- at&h: Show more Baseband Commands
Unlock
- at+clck: Traditional unlock command
- at+xlock: Wildcard unlock
- at+xsimstate: Print lock state (write at+xsimstate=1 to turn on, at+xsimstate=0 to turn off)
